Dressing gown with odor: a description of the construction patterns + tailoring children's robe with a hood

A robe for a home, a hospital or a bathhouse will sew a pattern of dressing gown with a smell that is a classic version of this clothing. Below we will analyze how to build a drawing, and the sewing technique with detailed comments.

Drawing pattern

You can draw on the fabric folded at once. This kimono robe goes without a side seam.

1. Measure the volume of the chest and thighs. Then from the fold, postpone a large amount divided by 2, plus 10-15 cm, so that the robe is not tight. Through the resulting point draw a straight line parallel to the fold - this is the middle of the transfer.
2. To retreat from the top point of the middle, pass the allowance for the seam of 1.5 cm and set the length of the transmission to the waist. Draw a line of the waist. Add to the last 12-15 cm is the allowance for the smell.
3. We make a non-tight armhole. To do this, measure from the waist line 13-15 cm up( the height to the armhole).
instagram viewer
4. Divide the pattern into 2 equal parts in width. In this case, the width of the shelf will be equal to the half obtained, plus 2 cm, and the size of the backrest - the obtained value minus 2 cm.
5. Now set the length of the back to the waist.
6. Make a neckline on the backrest with a depth of 3-4 cm and a width of 9-10 cm.
7. Construct a shoulder bevel 3 cm high, as shown.
8. Draw a local backrest arm line that runs perpendicular to the shoulder line.
9. Find the middle of the gear and measure 9-10 cm at the width of the neckline of the gear. Connect the outermost point of the waist( taking into account the smell) with a smooth line and the extreme point of the width of the neckline of the transmission. The bend should be minimal, so that the cutout does not turn out to be too big.
10. Lower the straight line parallel to the bend equal to the length of the product.
11. Make a shoulder line of the transfer with a height of 4 cm.
12. Draw a line of armhole from the extreme point of the shoulder - get the height of the side.
13. Sleeve is built like a shirt.
14. The design of a kimono dressing gown with a smell and sleeves has turned out.

In addition, you will need a fabric for processing the front edge and the waistband. If the maximum volume is up to 110 cm, then the tissue will be enough from the remnants of the pattern. In the case when the pattern is built on 56, 58 size more, and the maximum measurement is more than 110 cm, then you need 20 cm of fabric in addition.

Pattern dismantled in detail, just for beginners.

How to sew a bathrobe of terry towels?

For this we will need a pattern of a children's dressing gown with a hood for a baby 3-4 years old.

Take:

• two towels of the same color measuring 130 by 65 cm;
• needle;
• scissors;
• thread in tone to towels;
• sewing machine;
• ruler;
• white paper;
• pattern of children's dressing gown.

1. Build a pattern using the above illustration.

2. To make a hood, you can use a sweatshirt with a hood of the appropriate size.

3. Transfer the pattern to the fabric so that the edges of the towel correspond to the edges of the dressing gown.

4. Cut the parts and fold them together.

5. The places marked in the picture in red, cut with scissors.

6. Dock the pieces of the pattern, as shown below.

7. Sweep and stitch.

8. Then sew the sleeves.

9. It turned out a dressing gown that would suit both the girl and the boy.

Patterns of robes on the fastener

1. Pattern of a dressing gown on buttons with a belt for 54 sizes.

2. On the zipper.

Pattern for the 46th size. The length of the robe reaches the knee( 102 cm).Lightning need 70 cm. The allowances for seams should be left for 1 cm for shoulders, sides and lower cut. The edges of the neck opening and armholes are treated with an oblique bake. The increase in lightning is not done at the expense of its own width.
In conclusion: you can see about sewing gowns here.