How to weave ribbons from ribbons: ways of weaving with visual photos and tips for beginners, video lessons

Weaving baubles is a very entertaining process for any age. You can work with beads, threads, ribbons, and also include various accessories for decorating products. Macrame made of tapes is simpler in technique. About how to weave braces from ribbons for beginners and will go further speech.

Weaving from satin ribbon

To make a bracelet from ribbons faster than from beads and floss. This is their main advantage. Weaving products from one long or several bands( usually 2 or 4).

Method number 1: weaving in two tapes

For work it is necessary to take two meter ribbons of different, but combined with each other colors. They fold up. After retreating from the edges of 10 cm, tie the first knot.

Weaving is fastened with a pin, a needle or an adhesive tape for convenience. Next, make a loop of both bands and pass through each other.

One loop is tightened, the other remains. Again, make a loop with another tape and pass it through the rest, last tighten and so on until the end.

Method number 2: square bracelet

Needlework will need 4 ribbons 2 m in length. From the edge, indentation of 15 cm is made. Connect all tapes with a knot and lay out as a cross. A loop is made from the upper band.

Which is then covered with the right ribbon.

On the right, put the bottom.

And on the last one - the left one, which is looped through. Then tighten all the tapes in turn, starting with the first.

The process is then repeated in the same way.

Wearing a bracelet can be twisted it neatly in the form of a spiral, as shown in the photo.

Method number 3: round baubles

If in the first two ways to keep the shape of the tape are located freely, now the nodes must be tightened tight. In this paper we use bands 2.5 m long. They are folded in a cross and fixed in the middle. The weaving goes in the same way as the square. But as a result of tight tightening of belts the product is obtained in the form of a round bundle.

Such round shoelaces can be used not only for weaving bra, but also for handbags or handles for bags.

Method number 4: pigtail with beads

It is made very simply from three translucent tapes. The latter are superimposed on each other and pierced with a needle. A bead is threaded from above. Then the lower ribbon is turned away from itself and again is pushed onto the needle over the bead. Put the bead on again. Then again take the lower tape, turn on yourself and thread on the needle. So weaving goes to the end: the lower ribbons turn on themselves, then from themselves and between them are inserted beads. When weaving braids, an important condition must be observed: one can not stretch the ribbon on a string, it must go down by itself. Stretching is done once, when the bouquet has reached the right size. The result is this.

With the names

I have to say separately how to weave braces from ribbons with names. For this, schemes of letters are used, but only we need to weave not from tapes, but from floss.

Some tips for beginners

1. Ribbons should be taken the same length.
2. It is better to lighten the ends slightly, so that they do not shrink.
3. When knitting, it is desirable to tighten the knitting so that the ribbon does not wrinkle, except for the round braid.
4. The first time is better not to weave on weight until the skill is worked out.
5. Loops during operation and nodes can be temporarily fixed so that they do not dissolve.

In this article, only a small part of what represents macrame from a satin ribbon is written. The World Network hosts a lot of wonderful works that you can repeat or take as a basis the idea.

A selection of video clips on the topic of the article

Video how to weave braces from ribbons is a good demonstration of the process of needlework.

Today, any information on macrame is available, on the shelves there are all necessary means for this. It remains only to allocate a couple of hours and spend them alone with the ribbons, forgetting everything in the world.