How to tie a knot on a bracelet - we tie a knot on the bracelet

Very many are engaged in manufacturing of bracelets from beads. Sometimes you get whole masterpieces, real works of art. Indeed, things created by their own hands are unique and original. But often there is a certain difficulty, since many do not know how to tie a knot on a bracelet. And yet it is the strong knot that can guarantee the safety of all labor. Be careful and attentive! To make the bracelet an excellent decoration, you need to finish it well. Using a surgical node, it will be possible not to worry about this, since it is the most durable and reliable. The main thing - tie it right, because otherwise the knot will immediately untie and the bracelet will fly apart.

Surgical junction

So, first, use an elastic thread to keep the bracelet still. So it will not break at the sock and will not fall off your hands. Secondly, when you have finally collected it, cut the thread. You should have free tips somewhere about a centimeter and a half. Pull the thread and pull the ends a couple of centimeters. First, make a half-node: take one end of the thread and hold it with your hand, and the second at this time will need to be circled near the first. Happened? Now make the second same half-node.

How to fix the thread finally? Many needlewomen act like this: in the first half the thread is twisted twice. In the second half-circle, the thread is wound only once. In other words, you perform mirror actions relative to the very first node. This is the surgical site. Why surgical? Yes, because surgeons so connect the threads during the operation.

Here you have tightened the knot, cut the ends of the thread at a distance of about a half millimeter, now shove them into the nearest beads. Some use glue, fixing for greater reliability. Well, if you can not stain the bracelet with glue, then try. Each needlewoman has her own secrets.

Normal

Try this variant of the knot. One end of the thread is threaded into the loop on the other side. Now remove the knot from the loop and tie the ends of the thread together. True, this is not a very good option, since the sharp edge of the beads can break even the filament folded in half.

Sliding knot

Sliding knot - the first step To tie such a knot, it takes a little patience and a bit of assiduity. First, prepare the cotton lace is not too thick, no more than 90 cm long. Put the beads on it in the right order, weave the bracelet. And now - attention, tie a knot! Take the tips of the cord by hand, so that with each side there is a margin of 14 centimeters, direct them towards each other to meet them.

Sliding knot - second step Then its right tip is bent so that the tip is outside and placed with the edge( see the picture).The received loop should be fixed. Make sure that it is no more than 10 centimeters. Continue to work with the right tip, and on the left in the future will slide the knot.

Sliding knot - third step Set the left tip from left to right, circle the loop and part of the string several times, then gently lay the resulting "coils" in the direction opposite to you. Do three more such turns, holding the knot with your finger and adjusting the tension of the cord. Now pass the left and right tips through the loop obtained so that they can be pulled into the bundle. Just do not tighten it very much, because the turns must move freely. So we made the first nodule.

Sliding node - the last step of the We proceed to the next step, doing exactly the same actions as the first time. The resulting node will be passive. Next, make a loop on the second end of the lace, for which it is covered five times with a free tip and tighten the knot. A loop was obtained, into which the remaining end of the cord should be inserted. What is left can be cut. For special effect, the tips can be glued using universal adhesive.

Sometimes bracelet weave, bending the thread in half. How to tighten the knot in this case?

The ends of our thread must be two loops. These loops need to be worn on the right and left hands and tie the knot, without removing the hinges from the hands as follows:

With your right hand, cross the loop in the middle of the thread and hold it. At this time, the left hand should be put on the loop, tying the knot in such a way that our bracelet, put on the left hand, fit inside the loop. Now, under the bracelet, skip the loop and pull it out from under the bracelet. We release the left hand from the loop, release the thread and pull it. It turns out a node!

Another way: on the string or rope you need to make a loop, then put it on your hand, closer to the elbow of the loop that is on your hand. You pass the eyelet into the hole of another loop, tied on the arm, and you throw off the knot on the string.

Here are such ways of tying knots on a bracelet exist for today. Now you know them and can use them. Good luck!