Casket: patterns on the example of boxes from cardboard

A casket is necessary in every house, because all have small things that are convenient to store in it. But this casket can become a gift souvenir.

To make it, you need a pattern of the box. You will see it below, as well as a master class on its manufacture.

What is needed

• Thick cardboard;
• Colored paper or wallpaper;
• Adhesive;
• Pencil;
• Scissors;
• Scotch.

Job Description

Draw on the cardboard and cut out the patterns.

To make the folds of the cardboard smooth, you need to draw along the lines with the blunt side of the knife with a ruler. Ready-made patterns of the casket to assemble, as shown in the following photos:

Or you can make this original casket:

What is needed

• Thin white cardboard 30 × 40 cm;
• White canvas 30 × 40 cm.( Interweaving density 62 squares = 10 cm);
• PVA;
• Bead( diameter 3 mm.);
• Needle for beads;
• Silo( thin);
• White thread;
• White threads of a floss;
• Needle for embroidery.

Detailed description of the work

Stick the canvas onto the cardboard so that the rows of cells are even and there is no distortion. Wait until it dries. Cut out the prepared cardboard parts, as in the photo:

Make the stitches on each part with an awl( Fig. 2) and sweep the floss with threads.

Embroidery:

On the details A( 5 pcs.) To make embroidery according to figure 3, according to the principle of countable embroidery. Preliminary it is necessary to make a puncture with punctures on the front side, counting 2 cells in width and 2 in length. To sew embroidery with a seam "semicircle" with simple threads.

Details G embroider with blue beads.

Assembly:

Seal all parts with a connecting seam.

To make a bottom, you need to fold 2 pieces of B with sides to each other and sew around the perimeter.

To make an inner box, you need to fold the 4 pieces B short sides to each other and sew the inside in the form of a box. Embroider the bottom of the picture 5.

To make an outer box, you need to sew details A to each side of the inner box. Parts curl after attaching, since their length is greater than the height of the box( see Figure 6).Sew the parts between them.

To make the lid, you need 2 pieces A to be folded together and stitched around the perimeter. Sew the finished lid to one side of the inner box. Sew a series of beads to the loose sides of the lid.

The casket is ready. Patterns for free can be taken from this article.

Casket in the form of heart

You can make this kind of romantic casket. For example, on February 14 - the day of all lovers.

To make it, you need to draw a heart pattern on the paper and cut 2 hearts from thick cardboard( 1.75 mm thick).From cardboard, 1 mm thick, cut 2 pieces as in the photo.

Bend the fold line and sharpen edges and cuts.

Mark on the basis of 3 mm.from the edge of the boundary of the walls. Bend one sidewall, try on and cut off excess. Glue it from the front with paper and cram.

Do not go over the border, on the basis of applying glue, wait a few minutes for the glue to become more viscous.

Stick the wall, if there is excess, then cut off. But this should be done only after the glue has dried completely.

Similar to the side of the sidewall.

Cut 2 pieces of tape 10 cm and glue them.

Apply glue to the back of the tape and glue it to the lid.

Carefully close the lid and put it in the correct position.

Open and finally fix the tape.

Put the casket inside the paper. To do this, the height of the strip should be less than 1 mm.

Stick pieces of cardboard( 1 mm.) To the bottom so that it does not bend.

Cut the bottom detail so that it fits freely in the casket, but there were no gaps. Glued paper and paste, a little greased with glue, inside.

Do the same with the lid. Only this part should be smaller on all perimeter for 1-2 mm.

Make a new part for 3 mm.smaller than the lid, cut it out of cardboard( 1 mm.), edge the edges, cover with paper and again edge the edges. Stick on the lid.

It remains only to decorate - and that's it. A selection of videos related to