Poncho pattern: with sleeves, with a hood, for a full woman and many others

Today we will review many models, and start offering with a light one.

Easy poncho from chiffon

Poncho with an unusual combination of color and texture of fabrics from chiffon and silk looks very elegant:

This poncho pattern is very simple, you can cut it very quickly.

It is important the finishing details on the pattern are cut and cut separately.

Required chiffon details:

• One piece front half of the poncho;
• One piece of the back half of the poncho;
• Two details with folding sleeves poncho.
• One detail of the bottom trim transfers the poncho( cut out double) with the fold;
• One detail of the finish of the bottom of the back of the poncho( cut out double) with a fold;
• Two details of finishing the sleeves of a poncho( it is cut out double) with a fold.

Required silk parts:

This is a poncho pattern with sleeves

How to sew

The backrest and gear parts should be swept in to the back and transfer parts, respectively. At the bottom of the sleeves, sweep the finish. Shoulder stitches sweep and stitch, process allowances and iron seams. Double needle to adjust the neckline allowances. Sleeves sweep and stitch. Straighten the seams of the sleeves with one seam, as well as the side seams. Fold the free allowance in half inverted inside, turn, and then sweep by hand.

Poncho coat

The poncho coat is also unusual and elegant, especially when sewn on its own, but it can be done using a poncho coat

Building

Draw two lines from point B, one vertical down, the other horizontal to the left. On the horizontal line from the angle B, retreat one third of the crook of the neck +1.5 cm and one third of the neck's neck + 2 cm downwards. Form the neckline with the neckline.

To cut the neck on the back from point B, pull back down 2.5 cm. Cut through the pattern.

Delay the length of the shoulder plus the length of the sleeve and coat according to the measurement from the resulting points. Approach the approach to the bottom and clasp.

Cutting

Two parts of the half gears are required with a zippered approach, one back detail with a fold without a zipper, one piece with the collar of the collar of the coat rack. Two pieces of 10 × 20 cm for the belt.

Lining

From the fabric for the lining, cut two parts of the front half of the coat( up to the blue line), one backrest detail with a fold and one detail with the folding collar.

How to sew

Carry out the shoulder seams on the gear parts and the backrest from the lining and the base fabric.

Rectify seam allowances. Unscrew on the underside the integral collar and iron.

Fold the lining and the product face-to-face, sweep along the longitudinal seams to the side.

Attach and unscrew to front. On the lower edge, tuck in the allowances and sew by hand.

To strengthen the glued lining of the collar-stand, fold face-to-face with the collar from the lining and to stitch along the short and upper cut.

Unscrew and iron, then detach. Sweep the collar into the neck, apply a lining on top and stitch in one line, honing the lining along the neck.

Stitch 2 belts.

Sweep the hinges and sew on the buttons.

You can use any material you like, but made from drape such a poncho will not only warm, but also give chic its owner.

Poncho with hood

What is needed

Fabric, knitted adhesive fleece and slanting 6 cm wide.

Needs allowances for seams with double contour on patterns, with single allowances are not needed.

At the bottom of the sleeve and product allowances are 2 cm, and the remaining 1 cm.

The pattern of a poncho with a hood is almost no different from other kinds of ponchos, therefore it is also simple and does not require much time.

Cutting

Main fabric:

Back, shelf, front and back of the sleeve, large and small burlap, leaflet, 2 back parts and 1 front hood.

Such a poncho coat will fit perfectly on a full woman

How to sew

Duplicate the leaf with non-woven fleece, bend outward in the middle with the front side and iron. Place the pocket also duplicated with non-woven fleece. Mark a longitudinal line on a piece of paper that will determine the width of the finished sheet. Toss a small burlap on the inside of the leaves. Pritachit a piece of paper burlap down to the front side of the shelf, aligning the marking lines on the pocket and on the leaf. At short lines of a marking to finish the ends of lines. To the top line of a marking on a pocket to prick the big burlap. Between the lines of marking, cut the entrance into the pocket. Straighten seam allowances, then iron. Stitch the sacks through the corners of the pocket.

The middle section of the backrest is to stitch, sweep and iron the seam, and sweep the bottom section of the shelf and backrest. Lower the cut on the details of the shelf bend, then, double-stitch it to the side seam 16-20 cm.

Apply both shelves and fasten them to handle them as one piece.

To the shelf, pritochit the front of the sleeve, notch near the seam mark, sweep and iron on the shelf. The same is done with the back of the sleeve, just stitch it to the back.

Stitch along the shoulder sections of the shelves and the back, sweep and iron the seams on the back.

Simultaneously, sew up sections of the sleeve and side sections of the backrest and shelf. Wrap and iron the seams on the back.

The back of the hood pratachat to the front, sweep and iron the seams to the front. The middle section of the hood is to stitch, sweep and iron the seam. The length equal to the cutout of the hood plus 2 cm is to cut off the oblique bake. Stitch the bake in the ring, fold it outward along the front side and iron it. To obtachat, having put a strip from the front side on a cut of a hood, to bend and adjust on the basic detail along a bend, to iron a seam.

Insert the hood into the neck, sweep and iron the seam.

Bottom cut sleeve hose, bend to the wrong side, iron and tune. Lower the backrest section and bend and double-stitch it. Iron the seam.

Patterns of capes and ponchos are very easy to build on their own. To do this, you need to take a pattern of a jacket or blouse, if the pattern from the blouse is such, for example,

you will need to add width.

It is necessary to cut the pattern from point D to the bottom line and close the upper chest tuck.

For the construction of a sleeve this pattern is suitable http: // kroikashitie.com / wp-content /uploads/2010/09/ rukav1.jpg, which you need to divide into the back and front and paste to the appropriate places.

Cutout of the neck needs to be increased, the depth is 2-2.5 cm, and the width is about 1.5 cm.

Cut the pattern of the backrest over the relief, put the sleeve and slide it apart, respectively. The back is the same as the shelf, only without the allowance for the buckle, only the neck needs to be increased by 1 cm in depth, and in width as on the shelf by 1.5 cm.

Such capes or ponchos can be sewn from the fabric which is to your likingto you.